Installation method of deep groove ball bearings

Release time:

2023-09-08

Deep groove ball bearing installation method 1: Press fit: When the inner ring of the bearing is tightly matched with the shaft, and the outer ring is loosely matched with the bearing seat hole, a press can be used to press the bearing onto the shaft first, and then install the shaft together with the bearing. Put them into the bearing seat hole together. When pressing, place an assembly sleeve made of soft metal material (copper or mild steel) on the end face of the inner ring of the bearing.

Deep groove ball bearing installation method 1: Press fit: When the inner ring of the bearing is tightly matched with the shaft, and the outer ring is loosely matched with the bearing seat hole, a press can be used to press the bearing onto the shaft first, and then install the shaft together with the bearing. Put them into the bearing seat hole together. When pressing, place an assembly sleeve made of soft metal material (copper or mild steel) on the end face of the inner ring of the bearing. The outer ring of the bearing and the bearing seat hole fit tightly, and the inner ring and the shaft are When the fit is relatively loose, the bearing can be pressed into the bearing seat hole first. At this time, the outer diameter of the assembly sleeve should be slightly smaller than the diameter of the seat hole. If the bearing ring, the shaft and the seat hole are both tightly fitted, install the indoor ring and The outer ring should be pressed into the shaft and the seat hole at the same time, and the structure of the assembly sleeve should be able to press the end faces of the inner ring and the outer ring of the bearing at the same time.
Deep groove ball bearing installation method 2: Heating fit: By heating the bearing or bearing seat, the installation method uses thermal expansion to convert the tight fit into a loose fit. It is a common and labor-saving installation method. This method is suitable for large interference When installing the bearing, put the bearing or separable bearing ring into the oil tank and heat it evenly to 80-100°C before hot installation, then take it out of the oil and install it on the shaft as soon as possible. In order to prevent the inner ring end face and shaft shoulder from cooling, If the fit is not tight, the bearing can be tightened axially after cooling. When the bearing outer ring is tightly matched with the light metal bearing seat, the hot fitting method of heating the bearing seat can avoid scratches on the mating surface. When using an oil tank to heat a bearing, there should be a grid at a certain distance from the bottom of the tank, or a hook is used to hang the bearing. The bearing cannot be placed on the bottom of the tank to prevent impurities from entering the bearing or uneven heating. There must be a thermometer in the oil tank. Strictly control the oil temperature not to exceed 100°C to prevent the tempering effect and reduce the hardness of the ferrule.

LATEST NEWS

Precautions for bearing storage

In contact with corrosive chemical media, the bearing is not cleaned cleanly, there is dirt on the surface, or the bearing is touched with sweaty hands. After the bearing is cleaned, it is not packaged or installed in time, and it is exposed to the air for a long time, and is attacked by air moisture and contamination; contamination

2023-09-08

How to choose bearing lubricant?

Lubricant is an essential and necessary condition for the bearing to operate. It is an important adjustment to reduce bearing wear and improve bearing life. The lubrication methods of imported bearings can be divided into grease lubrication and oil lubrication. Different imported bearings have different uses. The method and the lubrication method used are also different. The following Demerui Bearing will share with you the influence of the choice of imported bearing lubricants on the bearing.

2023-09-08

Thrust Ball Bearings 2026 Guide: Selection, Performance, Real-World Use Cases

This 2026 comprehensive guide breaks down everything you need to know about thrust ball bearings, from core design principles and load-bearing capabilities to optimal selection workflows, maintenance routines, and real-world application performance. Drawing on 12+ years of hands-on manufacturing experience at Keyike Machinery, we share tested data on temperature limits, speed ratings, and failure prevention strategies to help engineering teams reduce downtime, extend component service life, and make cost-effective sourcing decisions for demanding operating environments.

2026-10-29

Thrust Ball Bearings 2026: Selection, Installation & Performance Guide

This 2026 evidence-based guide to Thrust Ball Bearings is built on 14 years of Keyike Machinery manufacturing experience, independent lab test data, and global industry engineering consensus. It covers core design principles, performance tradeoffs, verified installation workflows, common failure troubleshooting, and practical selection frameworks to help engineers, procurement teams, and maintenance specialists reduce downtime, optimize load efficiency, and avoid costly specification mismatches across high-axial-load applications.

2026-10-29

2026 Complete Guide to Thrust Ball Bearings: Selection, Performance & Use Cases

This 2026 comprehensive guide covers core design principles, data-driven selection steps, real-world performance benchmarks, and maintenance best practices for thrust ball bearings. Drawing on 18 years of hands-on manufacturing expertise from Keyike Machinery, the content helps engineers reduce downtime, optimize bearing life, and make informed procurement decisions for industrial equipment.

2026-10-22

Thrust Ball Bearings: 2026 Complete Guide to Selection, Performance & Maintenance

This expert 2026 guide draws on 12+ years of hands-on manufacturing and field service experience from Keyike Machinery to demystify thrust ball bearing fundamentals, performance metrics, selection processes, installation best practices, and common failure modes. It balances peer-reviewed industrial research with real-world case data to help engineering teams optimize bearing lifecycle and reduce operational costs.

2026-10-22