What are the classifications of tapered roller bearings?

Release time:

2023-09-08

Single row tapered roller bearings have an outer ring, an inner ring and a set of tapered rollers, which are composed of an inner ring assembly composed of a basket-shaped cage. The outer ring can be separated from the inner ring assembly. According to the ISO tapered roller bearing external dimension standard, any standard type of tapered roller bearing outer ring or inner ring assembly should be able to achieve international compatibility with the same type of outer ring or inner ring assembly. exchange.

Single row tapered roller bearings have an outer ring, an inner ring and a set of tapered rollers, which are composed of an inner ring assembly composed of a basket-shaped cage. The outer ring can be separated from the inner ring assembly. According to the ISO tapered roller bearing external dimension standard, any standard type of tapered roller bearing outer ring or inner ring assembly should be able to achieve international compatibility with the same type of outer ring or inner ring assembly. exchange. That is to say, the outer dimensions and tolerances of the same type of outer ring must comply with the provisions of ISO492 (GB307), and the cone angle of the inner ring components, the diameter of the cone of the components, etc. must also comply with the relevant regulations for interchangeability.
Usually, the cone angle of the outer ring raceway of a single row tapered roller bearing is between 10° and 19°, and it can withstand the combined effects of axial load and radial load at the same time. The larger the cone angle, the greater the ability to withstand axial load. Bearings with large cone angles have a suffix code of B. The cone angle is between 25° and 29°. They can withstand large axial loads. In addition, single row tapered roller bearings can adjust the clearance during installation.
The outer ring (or inner ring) of double row tapered roller bearings is a whole. The small end faces of the two inner rings (or outer rings) are similar, and there is a spacer in the middle. The clearance is adjusted by the thickness of the spacer, and the pre-interference of the double row tapered roller bearing can also be adjusted by the thickness of the spacer.
Four-row tapered roller bearings, the performance of this kind of bearing is basically the same as that of double-row tapered roller bearings, but it bears a larger radial load than double-row tapered roller bearings, and the limit speed is slightly lower. It is mainly used in heavy machinery.
Multi-sealed double and four-row tapered roller bearings, ZWZ provides long-life, multi-sealed double and four-row tapered roller bearings. Carry out a new personalized design for the bearing, change the traditional design method of the fully sealed bearing, and adopt a new type of sealing structure combining sealing and dustproof to improve the sealing effect and performance. Compared with open structure bearings, multi-sealed double and four-row tapered roller bearings have a service life increased by 20% to 40%; lubricant consumption is reduced by 80%.

LATEST NEWS

Precautions for bearing storage

In contact with corrosive chemical media, the bearing is not cleaned cleanly, there is dirt on the surface, or the bearing is touched with sweaty hands. After the bearing is cleaned, it is not packaged or installed in time, and it is exposed to the air for a long time, and is attacked by air moisture and contamination; contamination

2023-09-08

How to choose bearing lubricant?

Lubricant is an essential and necessary condition for the bearing to operate. It is an important adjustment to reduce bearing wear and improve bearing life. The lubrication methods of imported bearings can be divided into grease lubrication and oil lubrication. Different imported bearings have different uses. The method and the lubrication method used are also different. The following Demerui Bearing will share with you the influence of the choice of imported bearing lubricants on the bearing.

2023-09-08

Thrust Ball Bearings 2026 Guide: Selection, Performance, Real-World Use Cases

This 2026 comprehensive guide breaks down everything you need to know about thrust ball bearings, from core design principles and load-bearing capabilities to optimal selection workflows, maintenance routines, and real-world application performance. Drawing on 12+ years of hands-on manufacturing experience at Keyike Machinery, we share tested data on temperature limits, speed ratings, and failure prevention strategies to help engineering teams reduce downtime, extend component service life, and make cost-effective sourcing decisions for demanding operating environments.

2026-10-29

Thrust Ball Bearings 2026: Selection, Installation & Performance Guide

This 2026 evidence-based guide to Thrust Ball Bearings is built on 14 years of Keyike Machinery manufacturing experience, independent lab test data, and global industry engineering consensus. It covers core design principles, performance tradeoffs, verified installation workflows, common failure troubleshooting, and practical selection frameworks to help engineers, procurement teams, and maintenance specialists reduce downtime, optimize load efficiency, and avoid costly specification mismatches across high-axial-load applications.

2026-10-29

2026 Complete Guide to Thrust Ball Bearings: Selection, Performance & Use Cases

This 2026 comprehensive guide covers core design principles, data-driven selection steps, real-world performance benchmarks, and maintenance best practices for thrust ball bearings. Drawing on 18 years of hands-on manufacturing expertise from Keyike Machinery, the content helps engineers reduce downtime, optimize bearing life, and make informed procurement decisions for industrial equipment.

2026-10-22

Thrust Ball Bearings: 2026 Complete Guide to Selection, Performance & Maintenance

This expert 2026 guide draws on 12+ years of hands-on manufacturing and field service experience from Keyike Machinery to demystify thrust ball bearing fundamentals, performance metrics, selection processes, installation best practices, and common failure modes. It balances peer-reviewed industrial research with real-world case data to help engineering teams optimize bearing lifecycle and reduce operational costs.

2026-10-22